E30 E36 Delrin Round Shifter Carrier Bushing
Round Carrier Shifter Bushings (E24, E30, E28, E34)
Round Carrier Shifter Bushings (E24, E30, E28, E34)
Round Carrier Shifter Bushings (E24, E30, E28, E34)
Round Carrier Shifter Bushings (E24, E30, E28, E34)
Round Carrier Shifter Bushings (E24, E30, E28, E34)
Round Carrier Shifter Bushings (E24, E30, E28, E34)
E30 E36 Delrin Round Shifter Carrier Bushing
Round Carrier Shifter Bushings (E24, E30, E28, E34)
Round Carrier Shifter Bushings (E24, E30, E28, E34)
Round Carrier Shifter Bushings (E24, E30, E28, E34)
Round Carrier Shifter Bushings (E24, E30, E28, E34)
Round Carrier Shifter Bushings (E24, E30, E28, E34)
Round Carrier Shifter Bushings (E24, E30, E28, E34)

Round Carrier Shifter Bushings (E24, E30, E28, E34)

K0274-DL

Sale price $20.00 Save 0%
/


Only 37 items in stock!

ROUND CARRIER SHIFTER BUSHINGS (FOR: BMW E24, E30, E28, E34)

Well our round shifter carrier bushings do just that! Our Garagistic delrin or aluminum carrier bushings replace the original rubber bushing (which not only had lots of "give" but is usually neglected and degrades over time). These eliminate any side-to-side movement of the aluminum shifter carrier. These delrin shifter bushings fit at the front of the aluminum carrier so NO additional vibration or harshness will be felt. Replaces part number: 25 11 7 519 669 (25117519669). Installation instructions can be found here!

Please Note: One bushing might fit different the other bushing. Click here to learn why.

Compatibility
  • All E24 : 633csi, 635csi, M6
  • All E28: 528e, 535i, 535is, M5
  • All E30: 316, 318i, 325, 325e, 325i, 325is, 325ix, M3
  • E34: 525i, 530i, 535i, M5 (does not fit 540i)
  • E36: 318i, 318is, 325i, 325is
  • E46: 323i, 323ci, 325i, 325ci

Installation of Garagistic Delrin front carrier bushing (round).

Please Note: One bushing might fit different the other bushing. Click here to learn why.
Before staring, there is a certain tool that will make your life alot easier when installing these.
Its a "hook tool" Part number 926572 from Harbor Freight. It can be found here: http://www.harborfreight.com/8-inch-radiator-hose-pick-96572.html . You will use this hook tool to remove the "bitch clip". Buy this tool, it makes the job only take a few seconds.

removal of e30 bitch clip

E30 hook tool

  • The trans should be supported by the jack,
  • Lower the jack down until the jack pad is no longer touching the trans then go up slightly to hold it a small amount. you need to do this to allow the bitch clip to rotate back once its un-clipped.
  • With the hook pointed towards the driver side reach above next to the shift carrier and un-clip it.

 

Next is the removal of 1 13mm nut at the rear of the shift carrier.

  • Now you will have the shift carrier out of the car.
  • You need to remove the front carrier bushing.
  • Its a rubber bushing with a metal sleeve.

Use a exacto knife or a razor blade to cut the end of.

Once you cut the sleeve off you can push the rubber to the other side to remove it.

 

Now your shift carrier should be like this (or similar).

Now you may press the Garagistic front carrier bushing in.

garagistic delrin bushings

If you also bought the rear Delrin bushing. The following are the instructions for that.

 

Installation instructions for Garagistic rear Delrin bushing

Installation requires that the edge on the back of the carrier be grinded down a bit.

Before:

After:

You can see the metal file we used in this picture and the Garagistic rear Delrin bushing (can be bought here).

 

Next step is to burn out the old bushing on the rear carrier bracket.

Hammer in the new Delrin bushing with the chamfered end in first.

It may be a good idea to "dimple" the metal housings after putting the bushing in.This will ensure that the  bushing doesn't slip out the back. Use a punch and hammer for this process.